evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #1
So I'm back to this problem , more and more frequently now. Cleaning baskets and filters always fixed the issue before , but now we just did the filters 2 weeks ago and the pressure is normal , flow appears normal, no bubbling . Heater wont start sw open. We also get hi limit fault as well , since we've gotten the heater. I know folks say it's a flow problem , but there is no bypass and this is a 2 hp pump, puts out a lot of water. I'm at a loss what to check next ? Any ideas , getting cool and need the heater to not be ou tof commision.
Thanks !!
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Aug 27, 2023
- Add bookmark
- #2
Hi limit fault is a known problem. Some thermal insulation around the high limit sensors usually fixes it.
Read RayPak Heaters - Further Reading
What is your other problem?
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Aug 27, 2023
- Add bookmark
- #3
Remove the cartridges from your filter and see if it clears the SW OPEN error.
If so, clean or replace the cartridges and do a Overnight Chlorine Loss Test
1
1poolman1
TFP Expert
In The Industry
- Jul 14, 2014
- 7,580
- Sacramento
- Aug 27, 2023
- Add bookmark
- #4
evanwellens said:
So I'm back to this problem , more and more frequently now. Cleaning baskets and filters always fixed the issue before , but now we just did the filters 2 weeks ago and the pressure is normal , flow appears normal, no bubbling . Heater wont start sw open. We also get hi limit fault as well , since we've gotten the heater. I know folks say it's a flow problem , but there is no bypass and this is a 2 hp pump, puts out a lot of water. I'm at a loss what to check next ? Any ideas , getting cool and need the heater to not be ou tof commision.
Thanks !!
Be sure there is no damage to the pressure switch or wiring, its located on the in/out manifold behind the top removable panel.
How old is the heater? Some had an issue with the High Limit 2 switch that some insulation could solve.
Could be the internal bypass or Uni-Therm regulator causing the hi-limit to trip as well.
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #5
ajw22 said:
Hi limit fault is a known problem. Some thermal insulation around the high limit sensors usually fixes it.
Read RayPak Heaters - Further Reading
What is your other problem?
Yes the hi limit is a nuisance , but clears and resets. I do have it on my todo to find an insulation solution, just Leary that causes some damage if the temp is legit too high. SW Open is the other problem.
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #6
1poolman1 said:
Be sure there is no damage to the pressure switch or wiring, its located on the in/out manifold behind the top removable panel.
How old is the heater? Some had an issue with the High Limit 2 switch that some insulation could solve.
Could be the internal bypass or Uni-Therm regulator causing the hi-limit to trip as well.
I guess I need to find a exploded diagram to determine the location.
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Aug 27, 2023
- Add bookmark
- #7
The Hi Limit sensors still work as designed for protection with the external insulation on them.
The external insulation keeps other heat from causing them to trip prematurely.
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Aug 27, 2023
- Add bookmark
- #8
evanwellens said:
I guess I need to find an exploded diagram to determine the location.
Look in the Installation Manual.
1
1poolman1
TFP Expert
In The Industry
- Jul 14, 2014
- 7,580
- Sacramento
- Aug 27, 2023
- Add bookmark
- #9
evanwellens said:
I guess I need to find a exploded diagram to determine the location.
Remove the top panel above the inlet/outlet manifold (the plumbing side of the heater) and it is right on top to the left. Looks like a mushroom.
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #10
Thank you all for reaching out so soon. Did clean the filters again and replace. It worked but they really weren't that dirty. These are 2023 filters, and the pressure was very low, which usually indicates not dirty ( over the 12 years I have had this pool. Heater is like 5 years old.
Enjoying this content?
Support TFP with a donation.
Give Support
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #11
Just another observation , recently the heater has been making a moaning noise on occasion. Again on my todo to deep dive this problem , hoped it could wait until the season ended.
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Aug 27, 2023
- Add bookmark
- #12
Do a Overnight Chlorine Loss Test
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #13
ajw22 said:
Look in the Installation Manual.
will do thanks
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 27, 2023
- Add bookmark
- #14
ajw22 said:
Do a Overnight Chlorine Loss Test
What does that indicate ? Chlorine has been pretty steady all summer, I shock when needed and keep the chlorinator filled every 2 weeks.
W
wireform
Gold Supporter
Silver Supporter
TFP Guide
In The Industry
- Aug 15, 2017
- 6,821
- Spring Valley, NY
- Aug 27, 2023
- Add bookmark
- #15
Oclt will eliminate the fact or prove you have algae even if the water is crystal clear.
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Aug 28, 2023
- Add bookmark
- #16
wireform said:
Oclt will eliminate the fact or prove you have algae even if the water is crystal clear.
It's been crazy raining here , battling algae all summer
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Sep 14, 2023
- Add bookmark
- #17
Is there any chance adjusting the pressure switch a 1/4 turn might help ? Cleaning filters weekly is getting old quick
ajw22
TFP Expert
Gold Supporter
Silver Supporter
Bronze Supporter
TFP Guide
- Jul 21, 2013
- 55,965
- Northern NJ
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Sep 14, 2023
- Add bookmark
- #18
evanwellens said:
Is there any chance adjusting the pressure switch a 1/4 turn might help ? Cleaning filters weekly is getting old quick
Running your heater with inadequate pressure and flow can damage the heater and pipes.
Read Heater Flow Switch - Further Reading and check the Raypak Installation Manual on the pressure switch adjustment range or if you should replace it with a flow switch.
evanwellens
0
Silver Supporter
Bronze Supporter
- Jun 9, 2012
- 182
- Stony Point, NY
- Sep 14, 2023
- Add bookmark
- #19
Is there any chance adjusting the pressure switch a 1/4 turn might help ? Cleaning filters weekly is getting old quikc
ajw22 said:
Running your heater with inadequate pressure and flow can damage the heater and pipes.
Read Heater Flow Switch - Further Reading and check the Raypak Installation Manual on the pressure switch adjustment range or if you should replace it with a flow switch.
Thank you for your reply. So this heater has been running 5-6 years and this problem only came up recently, and frequently despite constant changing of filters ( actually came up once before and those filters needed to be changed and the pool filter pressure was high) . Also occurs when we turn our Polaris on. It's intermittent and seems to be at the edge of functionality , but becoming a real headache. I'd estimate the pool water level is 2-3 feet below the base of the heater, so it sees to fall within guidelines. So if a minor adjustment to the sensor is too risky , what do you think about just replacing it ?
D
danpik
0
TFP Guide
- Jun 4, 2012
- 1,757
- western NY
- Sep 14, 2023
- Add bookmark
- #20
evanwellens said:
Just another observation , recently the heater has been making a moaning noise on occasion. Again on my todo to deep dive this problem , hoped it could wait until the season ended.
My heater will do this if I forget to switch the pump to High. My old heater did the same thing. running mine on the high (2 speed pump) eliminates this.
Dan
Enjoying this content?
Support TFP with a donation.
Give Support
You must log in or register to reply here.